Sunday, February 21, 2016

Painting Jigs

First of all I must say I have been overwhelmed by the response to my last about my Rivendell Knight. Thanks so much for the support. It had 300 views in 12 hours and this week will probably end up taking over the second most post I have (which is currently occupied by a post I made over two years ago). The mini is currently stuck at 38 votes on CMON so if you have a second to register a vote I would greatly appreciate it and you can do so HERE.

Not a painted miniature for this post, but its related. I thought I would take you through my process for building painting jigs. I was tired of always having to hold the miniature by the model itself and scrape off paint, or attach the model to a base so I could paint it, because I usually make scenic bases after painting the model. I saw something similar to these somewhere and decided they were easy enough to build so I built my own. Shadow of Shadow and Flame recently asked me for some more so I built three different styles: A single mini jig (SMJ) with one bolt, a multi-mini jig (MMJ) with two bolts, and a half single mini jig for sculpting (HMJ) for Flame to try out and see how it works.

First step is to buy the proper material for the jigs.

NOTE: all measurements here are giving in the completely nonsensical  English units metric makes way too much sense to be used by 'Murica. So for my more sensible metric-using friends 1 inch (1") = 2.54cm.
Also, you can go to Online Conversion to convert any measurements here into what ever you want, so, for example, if you decide to make all your measurements in Furlongs, these guys have you covered.

1. Any length of 1 1/2" x 3/4" pine board (they make these out of all different wood but pine is cheapest)
2. 2" x 1/4" bolts with one nut and two washers per bolt.
3. miter box and saw (optional) any hand saw or electric saw will work
4. drill press (optional) any electric drill will work
5. 1/4" drill bit

I marked off the jigs into 2" sections for SMJs, 4" sections for MMJs, and 1" for HMJs. I have a miter box set up for cutting straight lines. Its not imperative that the lines are straight, but it makes for nicer jigs that are easier to work with. Cut the board up into the proper lengths, two pieces for each jig, for however many you need.

Side note: fishing gear and goose decoys pictured here are also an optional part of this process. Here is what they should look like when all cut up (except the HMJ is not pictured here):

The next step is to sand the edges and any rough faces. You're going to be using these alot and splinters suck so sand off all those burs from sawing the wood and then bevel the edges down a bit. IMPORTANT: mark what two sides of the jig are going to go together and DO NOT sand those edges. I made this mistake the first time around. The problem is that if you are going to paint your mini while it's attached to the base tag, that beveled edge will make it very difficult for the jig to grab the base tag. You want to keep that nice 90 degree angle here. The same holds true if you cut off the tag and drill a hole for a foot pin. You will have the same problem if the pin isn't long enough to get past the beveled edge. After sanding, your blocks of wood will look spectacular.

The next step is to mark off and drill your holes for the bolts. for SMJs the hole is right in the center, 3/4" down and 1" in from the edge.  For MMJs they are 3/4" down  from the top and each bolt is measured 1" in from the outside. For HMJs the hole is 1/2" in and 3/4" down. OK, for this step I used a drill press and drill press vise. Again, this is completely optional, any electrical drill will work. However the drill press affords you the opportunity to drill straight holes which will allow the jig blocks to move more easily along the bolt. Clamp both halves of the jig into the vise and drill through both at the same time (to ensure the holes line up properly) with a 1/4" drill bit. IMPORTANT: For the MMJs, after drilling the first hole, run the bolt through the hole to hold the halves in place. This will ensure that the two haves don't slip any when you move to drill the other hole and the jigs will slide along each bolt much more easily.

We are getting there now. Put a washer on one end of the bolt and run it through the jig halves. Place another washer on the other end and then the nut. The size of the washer is optional. I think I used 7/8", but the bigger the diameter of the washer the more surface area of the jig sides it will apply pressure to when you tighten down the nut. I haven't had any problems with the size I am using, but you can't go wrong with larger ones:

Note: Pictured here are actually 2 1/2" bolts. They are good because you can open the jigs up further if you need to. However, this particular type of bolt is not threaded all the way to the top so the nut just barely holds the jig edges together. I like the 2" better. You just want to make sure that when the jig is closed on your mini you have threads sticking out of the side, and not the threaded part if you get that type of bolt.

Here is a picture of a jig in action, I know, breathtaking to see it work isn't it?


Final step: Congratulate yourself on a job well done, then slap a miniature in there and sling some paint at it. 

I have a few miniatures I need to get photographed and uploaded so hopefully I'll have something new up here this week. In the meantime, I hope you found this useful.





Monday, February 15, 2016

I've put this off for far too long.....Rivendell Knight

This miniature has been one of the strangest journeys for me. I started it largely to test myself at painting a grey horse. Then, for what ever reason I totally and completely lost interest in finishing the knight. It has sat on the paint station, been in the background of other photos, and generally been used as comedic insult to me for well over a year. Then last week I got inspired to paint it. I am now so enthused about it that I cant wait to paint another. In the end I think it was the cloak. I think the sculpts themselves are wonderful. And the dynamic sense they give is great. However the huge surface area was a real challenge for me and that is what hung me up on finishing it. I had it a brown color not unlike the box art and it never appealed to me. And I never really had a nice theme to tie it all together. I was inspired to do some freehand work and it was either dig out some knights of Dol Amroth or paint this guy right in front of me. After that it just snowballed. I settled on a scheme and repainted parts I had already done, updated the armor and edged it all in three shades of gold and painted the banner to match which went through a few color changes itself. Wet blending and I became good friends on this one. Anyway, it was an absolute joy to paint and I am really happy with it. I plan to submit it to Warhammer Visions so they can reject it! Here it is.....finally:

As always, thanks for looking!

UPDATE: I added this guy to my CMON gallery. If you have a second to spare and could cast a vote clcik HERE. I would greatly appreciate it!